| DISPLAYED ALARM | E-CODE BREAKDOWN | DESCRIPTION | NOTES |
|---|---|---|---|
| Controller Fault | No E-code on HSB | Replace Controller | |
| Overcrank | 1100 | Condition - Engine Cranks but will not Start Unit turns over but will not start. Controller is receiving signal on Wire 18. | Problem 17 |
| Overspeed | 1200 | Prolonged Over 72 Hz for 3 seconds. Possible cause: Stepper motor/mixer body assembly issue. | Test 12 |
| Overspeed | 1205 | Instantaneous Over 75Hz for .1 second (100 milliseconds). Possible cause: Stepper motor/mixer body assembly issue. | Test 12 |
| Low Oil Pressure | 1300 | Occurred while running The default Extended alarm for low oilpressure. Check oil level and pressure. | Test 61 |
| High Temperature | 1400 | Condition - Air Flow Impeded I Flow Issue Check the inleUoutlet for debris. | Test 62 |
| RPM Sensor | 1501 | Twin Cylinder+Running Twin Cylinder Running faults to RPM sensor loss. Possible Causes: air pocket in fuel line. dirty fuel, missing ignition pulse (loss of one of the primary coils). | Test 50 and Test 64 |
| RPM Sensor | 1505 | Twin Cylinder+Cranking Twin Cylinder Cranking faults to RPM sensor loss Possible Cause: starter motor issue, missing ignition pulse (loss of one of the primary coils). | If engine cranks, Test 64. If engine does not crank, Problem 15. |
| RPM Sensor | 1511 | Single Cylinder+Running Single Cylinder Running with Low Fuel Pressure faults to RPM sensor loss Possible Causes: air pocket in fuel line,dirty fuel. | Test 50 and Test 64 |
| RPM Sensor | 1515 | Single Cylinder+Cranking Single Cylinder Cranking faults to RPM sensor loss Possible Cause: starter motor issue. | If engine cranks, Test 64. If engine does not crank, Problem 15. |
| Underspeed | 1600 | Condition - Unit is Overloaded Unit is Overloaded slowing engine speed, fuel supply low or throttle control problem. | Problem 1, Test 50 or Test 12 |
| Overvoltage | 1800 | Prolonged Over-Voltage | Problem 2 |
| Undervoltage | 1900 | Prolonged Under-Voltage Undervoltage due to loss of voltage for some time (10+ seconds). | Test 5 |
| Undervoltage | 1901 | Instantaneous Undervoltage due to sudden loss of voltage. | Problem 1 |
| Undervoltage | 1902 | Both Zero Crosses missing Undervoltage due to faulty excitation winding.or zero cross circuit.or circuit in general. Possible cause: loose wiring, field boost hardware failure | Problem 1 |
| Undervoltage | 1906 | Single Zero Cross missing Undervoltage due to faulty excitation winding , zero cross circuit, or circuit in general. Possible cause: field boost hardware failure | Problem 1 |
| Wiring Error | 2099 | Customer connection low voltage and high voltage wires are crossed. | Check customer connection in generator |
| Overload Remove Load | 2100 | Overloaded - Default (Output Current Method) Unit is overloaded, one of the two CTs is detecting an overload condition. Check transfer switch loadshed functionality. (Change load dynamics or utilize loadshed). | Remove Load |
| Undervoltage Overload | 2299 | Unit was overloaded and attempted to start with a large load connected. The unit can not ramp up the generator voltage to its normal target volt- age value if it starts with a large load connected | Remove Load |
| Stepper Overcurrent | 2399 | Current flow in stepper coil(s ) above specification | Test 12 |
| Fuse Problem | 2400 | Missing I Damaged Fuse The 7.5 amp Controller Fuse is missing or blown (open). | Test 44 |
| Low Battery | Condition-> Battery less than 12.1Volts for 60 seconds | Test 45 | |
| Battery Problem | Condition-> More than 16 Volts of battery voltage or 600 milliamperes or more of charge current at the end of an 18 hour charge | Test 45 | |
| Charger Warning | Less than 12.5 volts of battery voltage at the end of a 18 hour charge | Problem 22 | |
| Charger Missing AC | AC power is missing from the battery charger input | Problem 22 | |
| SEEPROM Abuse | Condition-> more than 1200 writes to the EEPROM in a 5 minute period. |
Evolution Error Codes
This guide is rated 3 out of 5.
Did this help you?